Chain · RK

What Is Chain Stretch, How Is It Measured and What Should You Do?

Velomoto teknik ekibiUpdated: 4 min read

Measuring 20 pitches on a chain with a ruler and the increase in stretch (illustrative)

Short answer

Chain stretch is not the metal stretching; it is the pitch of every link growing slightly because of wear between the pin and bushing. The wear is irreversible; a stretched chain needs frequent adjustment and wears the sprockets, and when it reaches the service limit the chain and sprockets are replaced together.

Stretch is checked by measuring a set number of pitches with a ruler. On a new 520, 525 or 530 chain, 20 pitches (across 21 pins) measure 317.5 mm; the measured value is compared with the limit in the service manual.

Velomoto is the official distributor of RK Japan in Turkey.

Why does a chain stretch?

As the chain runs, the pins rotate inside the bushings and both surfaces wear. The small play that forms in each link adds up along the chain, and the chain stretches. Lack of lube, dirt, rust, too-tight adjustment and hard launches accelerate stretch. In O-ring chains, the grease inside slows wear; that is why O-ring chains stretch later.

A new chain beds in slightly during the first kilometers. RK's heavy duty chains are pre-stretched at the factory to reduce this initial stretch.

How is stretch measured?

1. Pitch measurement (the most reliable method)

  1. Position the chain so that the lower run is taut (for example by turning the wheel slightly forward).
  2. Starting from the center of one pin, measure to the center of the 21st pin, that is, 20 pitches.
  3. Compare the value with the length of a new chain and the service limit in the manual.
  4. Repeat the measurement at several different places on the chain.
Chain sizePitch20 pitches on a new chain
420, 42812.7 mm (1/2″)254.0 mm
520, 525, 53015.875 mm (5/8″)317.5 mm

The service limit varies by manufacturer and model; use the value in your motorcycle's manual.

2. Rear sprocket test (quick check)

Pull the chain backward away from the rear of the rear sprocket, at the 3 o'clock position. If more than half a tooth is exposed, the chain is worn. This test is no substitute for an exact measurement.

3. Adjustment range

If the adjustment range on the swingarm is nearly used up, the chain is badly stretched.

Uneven stretch: loose in one place, tight in another

If, as you turn the wheel, the chain is tight at one point and loose at another, the chain has not worn evenly. The causes are:

  • Some links wearing or stiffening more than others
  • A worn or bent sprocket
  • Long use dry and dirty

Always adjust according to the tightest point. If the difference between the tight and loose points is pronounced, the chain has reached the end of its life; replace the chain and sprockets together.

What to do with a stretched chain

ConditionWhat to do
Stretch below the service limitClean, lubricate, adjust the slack
At or above the service limitReplace the chain and sprockets together
Adjustment range used upReplace the chain and sprockets together
Pronounced uneven stretchReplace the chain and sprockets together

Shortening a stretched chain by removing links is not a solution: the chain's pitch has grown and it does not seat on the sprockets. In addition, for the O-ring 520EXW, 520MAX-X and 520MAX-O chains, RK recommends replacing the chain immediately if the inner plate height drops below 13.5 mm.

RK logo

Products in this guide

RK chains and sprockets

Chains and heat-treated sprockets made in Japan since 1953; original equipment supplier to many manufacturers including Honda, Yamaha, Suzuki and Kawasaki. 1,119 products and 3,786 model applications in the catalog.

We do not sell directly to end users; you can find the products at our authorised dealers. See our dealers

Frequently asked questions

Why does a chain stretch?

Because of wear between the pin and bushing. The metal itself does not stretch.

Can a stretched chain be fixed?

No. Wear is irreversible; at the limit, the chain and sprockets are replaced.

How can I tell the chain has stretched?

It needs frequent adjustment, the adjustment range runs out, the chain can be pulled back off the rear sprocket, and the 20-pitch measurement exceeds the limit.

The chain is loose in one place and tight in another; why?

The chain or sprocket has not worn evenly. Adjust according to the tightest point; if the difference is pronounced, replace the set.

Can links be removed from a stretched chain?

Not recommended; the chain's pitch has grown and it wears the sprockets quickly.

How much does an RK chain stretch?

The rate of stretch depends on the series, seal type, maintenance and use; a well-maintained O-ring chain stretches later.